Radtel RT-910_BT programming software
Open WebCHIRPWebCHIRP programs the Radtel RT-910_BT in your browser. It runs the CHIRP project's own driver for this radio, so it reads and writes the same codeplug the desktop software does — without installing anything.
No driver install needed
Radtel programming cables use a CH340, CP2102, PL2303 or FTDI USB-serial chip. WebCHIRP speaks to all four directly from the browser, so there is no driver package to download and no Windows version to match. Plug the cable in and pick the port when the browser asks.
What you can edit on the RT-910_BT
- 960 memory channels, numbered 1 to 960
- Channel names up to 12 characters
- Transmit power: High 8.0W, Middle 4.0W, Low 1.0W
- Modes: AM, FM, NAM, NFM
- Bands: 18–1000 MHz
- Tone squelch: Cross, DTCS, TSQL, Tone
- Radio-wide settings, not just the channel list
RT-910_BT hardware
Researched from the sources listed below — spec sheets, manuals and retailer listings — rather than taken from the CHIRP driver. Anything not established is left out.
| Type | Handheld |
|---|---|
| Battery | 1800 mAh |
| Charging | USB-C, Desktop charging cradle |
| Transmit power | Up to 5 W |
| Modulation | FM, AM, WFM |
| Display | Yes |
| Still manufactured | Yes |
| Dual receive | No |
| APRS | No |
| GPS | No |
| Bluetooth programming | Yes |
Frequency bands
| Band | Receive | Transmit |
|---|---|---|
| 6 m | 45–59 MHz | 45–59 MHz |
| FM broadcast | 65–108 MHz | — |
| Airband | 108–136 MHz | — |
| Other | 136–260 MHz | 136–260 MHz |
| General coverage | 260–299 MHz | — |
| Other | 300–520 MHz | 300–520 MHz |
Sold as the RT-910B, the Bluetooth app-programming version. 6 m TX spans 45–59 MHz; other TX spans are continuous 136–260 and 300–520 MHz.
Sources: radtels.com
Can I update the firmware on the RT-910_BT?
Radtel publishes firmware updates, though not for every radio it has made. Its download page is where to check whether the RT-910_BT is one of them. Most of the RT- range has a firmware update file alongside its CPS.
Firmware downloads at radtels.com
WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.
How to program a Radtel RT-910_BT
- Plug the programming cable into the radio and the computer.
- Open WebCHIRP, check Radtel RT-910_BT is selected, and press Download.
- Edit the channels, or pull in nearby repeaters from a directory.
- Press Upload to write the result back to the radio.
Questions
Do I need to install a USB driver to program the Radtel RT-910_BT?
No. WebCHIRP talks to CH340, CP2102, PL2303 or FTDI programming cables from the browser, so there is nothing to install on Windows, macOS or Linux.
Do I need the Radtel CPS software?
No. WebCHIRP runs CHIRP's own Radtel RT-910_BT driver in the browser, so it reads and writes the same codeplug the desktop software does.
How many channels does the Radtel RT-910_BT hold?
960, numbered 1 to 960 in the channel table.
Can I update the firmware on the Radtel RT-910_BT?
Radtel publishes firmware updates, though not for every radio it has made. Its download page is where to check whether the RT-910_BT is one of them. Most of the RT- range has a firmware update file alongside its CPS. WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.