Quansheng TK11 programming software
Open WebCHIRPWebCHIRP programs the Quansheng TK11 in your browser. It runs the CHIRP project's own driver for this radio, so it reads and writes the same codeplug the desktop software does — without installing anything.
No driver install needed
Quansheng programming cables use a CH340, CP2102, PL2303 or FTDI USB-serial chip. WebCHIRP speaks to all four directly from the browser, so there is no driver package to download and no Windows version to match. Plug the cable in and pick the port when the browser asks.
What you can edit on the TK11
- 999 memory channels, numbered 1 to 999
- Channel names up to 16 characters
- Transmit power: Low 1.0W, Middle 5.0W, High 10W
- Modes: AM, CW, FM, LSB, NFM, USB
- Bands: 0.15–1160 MHz
- Tone squelch: Cross, DTCS, TSQL, Tone
- Radio-wide settings, not just the channel list
TK11 hardware
Researched from the sources listed below — spec sheets, manuals and retailer listings — rather than taken from the CHIRP driver. Anything not established is left out.
| Type | Handheld |
|---|---|
| Battery | 2500 mAh |
| Charging | USB-C, Desktop charging cradle |
| Transmit power | 1–10 W |
| Modulation | FM, AM, SSB, WFM |
| Display | Yes |
| Still manufactured | Yes |
| Dual receive | No |
Frequency bands
| Band | Receive | Transmit |
|---|---|---|
| General coverage | 0.153–1160 MHz | — |
| 10 m | 25–29.8 MHz | 25–29.8 MHz |
| 6 m | 50–54 MHz | 50–54 MHz |
| VHF | 135–174 MHz | 135–174 MHz |
| UHF | 350–490 MHz | 350–490 MHz |
Export version shown: TX 25–29.8, 50–54, 135–174 and 350–490 MHz (5 W on 10 m/6 m, 10 W VHF/UHF); the US version is ham-band limited. SSB is receive only.
Sources: sinotel.co.uk · hamimports.com
Can I update the firmware on the TK11?
Quansheng publishes a firmware update for the TK11 that you can install yourself. Quansheng publishes TK11/TK11(8) firmware and programming software.
Firmware downloads at en.qsfj.com
WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.
How to program a Quansheng TK11
- Plug the programming cable into the radio and the computer.
- Open WebCHIRP, check Quansheng TK11 is selected, and press Download.
- Edit the channels, or pull in nearby repeaters from a directory.
- Press Upload to write the result back to the radio.
Questions
Do I need to install a USB driver to program the Quansheng TK11?
No. WebCHIRP talks to CH340, CP2102, PL2303 or FTDI programming cables from the browser, so there is nothing to install on Windows, macOS or Linux.
Do I need the Quansheng CPS software?
No. WebCHIRP runs CHIRP's own Quansheng TK11 driver in the browser, so it reads and writes the same codeplug the desktop software does.
How many channels does the Quansheng TK11 hold?
999, numbered 1 to 999 in the channel table.
Can I update the firmware on the Quansheng TK11?
Quansheng publishes a firmware update for the TK11 that you can install yourself. Quansheng publishes TK11/TK11(8) firmware and programming software. WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.