Icom IC-M710 programming software
Open WebCHIRPWebCHIRP programs the Icom IC-M710 in your browser. It runs the CHIRP project's own driver for this radio, so it reads and writes the same codeplug the desktop software does — without installing anything.
No driver install needed
Icom programming cables use a CH340, CP2102, PL2303 or FTDI USB-serial chip. WebCHIRP speaks to all four directly from the browser, so there is no driver package to download and no Windows version to match. Plug the cable in and pick the port when the browser asks.
What you can edit on the IC-M710
- 232 memory channels, numbered 0 to 231
- Channel names up to 6 characters
- Modes: AM, CW, DIG, FSK, LSB, USB, USB
- Bands: 1–30 MHz
IC-M710 hardware
Researched from the sources listed below — spec sheets, manuals and retailer listings — rather than taken from the CHIRP driver. Anything not established is left out.
| Type | Base station |
|---|---|
| Transmit power | 20–150 W |
| Modulation | SSB, AM, CW, RTTY |
| Display | Yes |
| Still manufactured | No |
| Dual receive | No |
| APRS | No |
| GPS | No |
| Bluetooth programming | No |
Frequency bands
| Band | Receive | Transmit |
|---|---|---|
| General coverage | 0.5–29.9999 MHz | — |
| Marine | 1.6–2.9999 MHz | 1.6–2.9999 MHz |
| Marine | 4–4.9999 MHz | 4–4.9999 MHz |
| Marine | 6–6.9999 MHz | 6–6.9999 MHz |
| Marine | 8–8.9999 MHz | 8–8.9999 MHz |
| Marine | 12–13.9999 MHz | 12–13.9999 MHz |
| Marine | 16–19.9999 MHz | 16–19.9999 MHz |
| Marine | 22–22.9999 MHz | 22–22.9999 MHz |
| Marine | 25–27.5 MHz | 25–27.5 MHz |
MF/HF marine SSB; 60 W PEP above 24 MHz. Succeeded by the IC-M803.
Sources: icomjapan.com · mobilesystems.nz · icomjapan.com
Can I update the firmware on the IC-M710?
Icom publishes firmware updates, though not for every radio it has made. Its download page is where to check whether the IC-M710 is one of them. Many older models have no firmware download at all.
Firmware downloads at icomjapan.com
WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.
How to program a Icom IC-M710
- Plug the programming cable into the radio and the computer.
- Open WebCHIRP, check Icom IC-M710 is selected, and press Download.
- Edit the channels, or pull in nearby repeaters from a directory.
- Press Upload to write the result back to the radio.
Questions
Do I need to install a USB driver to program the Icom IC-M710?
No. WebCHIRP talks to CH340, CP2102, PL2303 or FTDI programming cables from the browser, so there is nothing to install on Windows, macOS or Linux.
Do I need the Icom CPS software?
No. WebCHIRP runs CHIRP's own Icom IC-M710 driver in the browser, so it reads and writes the same codeplug the desktop software does.
How many channels does the Icom IC-M710 hold?
232, numbered 0 to 231 in the channel table.
Can I update the firmware on the Icom IC-M710?
Icom publishes firmware updates, though not for every radio it has made. Its download page is where to check whether the IC-M710 is one of them. Many older models have no firmware download at all. WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.