BTECH UV-50X2_G2 programming software
Open WebCHIRPWebCHIRP programs the BTECH UV-50X2_G2 in your browser. It runs the CHIRP project's own driver for this radio, so it reads and writes the same codeplug the desktop software does — without installing anything.
No driver install needed
BTECH programming cables use a CH340, CP2102, PL2303 or FTDI USB-serial chip. WebCHIRP speaks to all four directly from the browser, so there is no driver package to download and no Windows version to match. Plug the cable in and pick the port when the browser asks.
What you can edit on the UV-50X2_G2
- 200 memory channels, numbered 0 to 199
- Channel names up to 8 characters
- Transmit power: High 50W, Low 10W
- Modes: FM, NFM
- Bands: 130–180 MHz, 400–521.05 MHz
- Tone squelch: Cross, DTCS, TSQL, Tone
- Radio-wide settings, not just the channel list
UV-50X2_G2 hardware
Researched from the sources listed below — spec sheets, manuals and retailer listings — rather than taken from the CHIRP driver. Anything not established is left out.
| Type | Mobile |
|---|---|
| Transmit power | 5–50 W |
| Modulation | FM, WFM |
| Display | Yes |
| Still manufactured | Yes |
| Dual receive | No |
| Cross-band repeater | No |
| APRS | No |
| GPS | No |
| Bluetooth programming | No |
Frequency bands
| Band | Receive | Transmit |
|---|---|---|
| FM broadcast | 65–108 MHz | — |
| VHF | 136–174 MHz | 136–174 MHz |
| UHF | 400–520 MHz | 400–520 MHz |
Sources: baofengtech.com · commgearsupply.com
Can I update the firmware on the UV-50X2_G2?
BTECH publishes no firmware update for the UV-50X2_G2: its radios are programmed at the factory, and their firmware is not meant to be replaced. Its firmware downloads cover the DMR and PRO-series radios; the analog FRS, GMRS, MURS and UV sets get CPS only.
BTECH downloads at baofengtech.com
WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.
How to program a BTECH UV-50X2_G2
- Plug the programming cable into the radio and the computer.
- Open WebCHIRP, check BTECH UV-50X2_G2 is selected, and press Download.
- Edit the channels, or pull in nearby repeaters from a directory.
- Press Upload to write the result back to the radio.
Questions
Do I need to install a USB driver to program the BTECH UV-50X2_G2?
No. WebCHIRP talks to CH340, CP2102, PL2303 or FTDI programming cables from the browser, so there is nothing to install on Windows, macOS or Linux.
Do I need the BTECH CPS software?
No. WebCHIRP runs CHIRP's own BTECH UV-50X2_G2 driver in the browser, so it reads and writes the same codeplug the desktop software does.
How many channels does the BTECH UV-50X2_G2 hold?
200, numbered 0 to 199 in the channel table.
Can I update the firmware on the BTECH UV-50X2_G2?
BTECH publishes no firmware update for the UV-50X2_G2: its radios are programmed at the factory, and their firmware is not meant to be replaced. Its firmware downloads cover the DMR and PRO-series radios; the analog FRS, GMRS, MURS and UV sets get CPS only. WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.