Baofeng UV-9G programming software
Open WebCHIRPWebCHIRP programs the Baofeng UV-9G in your browser. It runs the CHIRP project's own driver for this radio, so it reads and writes the same codeplug the desktop software does — without installing anything.
No driver install needed
Baofeng programming cables use a CH340, CP2102, PL2303 or FTDI USB-serial chip. WebCHIRP speaks to all four directly from the browser, so there is no driver package to download and no Windows version to match. Plug the cable in and pick the port when the browser asks.
What you can edit on the UV-9G
- 128 memory channels, numbered 0 to 127
- Channel names up to 7 characters
- Transmit power: High 5.0W, Med 1.0W, Low 0.5W
- Modes: FM, NFM
- Bands: 130–180 MHz, 400–521 MHz
- Tone squelch: Cross, DTCS, TSQL, Tone
- Radio-wide settings, not just the channel list
UV-9G hardware
Researched from the sources listed below — spec sheets, manuals and retailer listings — rather than taken from the CHIRP driver. Anything not established is left out.
| Type | Handheld |
|---|---|
| Transmit power | 0.5–5 W |
| Modulation | FM |
| Display | Yes |
| Still manufactured | Yes |
| Dual receive | No |
| Cross-band repeater | No |
| APRS | No |
| GPS | No |
| Bluetooth programming | No |
Frequency bands
| Band | Receive | Transmit |
|---|---|---|
| FM broadcast | 65–75 MHz | — |
| FM broadcast | 76–108 MHz | — |
| VHF | 136–174 MHz | — |
| UHF | 400–480 MHz | — |
| GMRS | 462.55–467.725 MHz | 462.55–467.725 MHz |
IP67 GMRS radio; VHF (136–174 MHz) and UHF (400–480 MHz) coverage is receive only.
Sources: baofengradio.com · baofeng.s3.amazonaws.com
Can I update the firmware on the UV-9G?
Baofeng publishes a firmware update for the UV-9G that you can install yourself. Baofeng's download area includes a UV-9G firmware update that enables transmit on channel 15.
Firmware downloads at baofengradio.com
WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.
How to program a Baofeng UV-9G
- Plug the programming cable into the radio and the computer.
- Open WebCHIRP, check Baofeng UV-9G is selected, and press Download.
- Edit the channels, or pull in nearby repeaters from a directory.
- Press Upload to write the result back to the radio.
Questions
Do I need to install a USB driver to program the Baofeng UV-9G?
No. WebCHIRP talks to CH340, CP2102, PL2303 or FTDI programming cables from the browser, so there is nothing to install on Windows, macOS or Linux.
Do I need the Baofeng CPS software?
No. WebCHIRP runs CHIRP's own Baofeng UV-9G driver in the browser, so it reads and writes the same codeplug the desktop software does.
How many channels does the Baofeng UV-9G hold?
128, numbered 0 to 127 in the channel table.
Can I update the firmware on the Baofeng UV-9G?
Baofeng publishes a firmware update for the UV-9G that you can install yourself. Baofeng's download area includes a UV-9G firmware update that enables transmit on channel 15. WebCHIRP does not flash firmware. It reads and writes the channel list and settings over the programming cable, which is a separate part of the radio.